Polimer

Electronic polymizer. Firing of acrylic resin at variable pressure and cylinder pressurisation.

Check out the VIDEO TRAINING about the Prothyl Evo on line.

Advantages

  • Robust stainless steel structure which makes the equipment extremely dependable
  • Satisfies all technical requirements requested for resins treatment
  • Durable and easy maintenance
  • 4 discharge cycles (air/water) can be set and can be combined with 2 cooling cycles (slow/fast)
  • 1-year warranty

Characteristics

  • Front panel display shows polymerizer temperature and time
  • Up to 10 memorisable programs
  • Setting of working time from 1 minute to 99 hours
  • 100% stainless steel support structure
  • Safety microswitch which detects opening of lid
  • Internal machine safety valve
  • Equipped with filter with air pressure regulator
  • Self-locking lid closure
  • Polimer are able to contain 2 self-standing medim size flask
  • Maximum working pressure 6 bar
  • Precise and flexible electronic controlo allow an optimal treatment of resins

 

C305701 POLIMER 86    Discontinued product, available while supplies last.

Technical Data

Polimer 180

Size (cm)L41 cm / D38 cm / H30 cm
Basin size Ø18 / H 14 cm
Total power 1600 Watt max
Voltage (V - Hz)230 V ± 10% / 50-60 Hz
Weight 25 Kg

Packaging

C305702Polimer 180 Polymerizer

Standard components

XD0070200Stainless perfored work holder for polimer 180
XR0070095Work holder support with pliers for polimer 180
XI00700405 litres polythene drum
 8/6 transparent 2 metre Rilsan tube

Accessories

 

C08000Self-standing brass flask
XI0070030Work holder pliers for polimer 86 - 180 ( 4 pcs)

 

Troubleshooting

ISSUECAUSEREMEDY
After powering the equipment via the
main switch the on-key LED fails to
come on.
1. Plug is not connected to
the mains socket.
Power lead is damaged.
2. Fuse blown.
1. Connect the plug to the mains
socket properly.
Have the power lead replaced by
an
Authorised Service Centre
only.
2. Change the fuse, using one of
identical characteristics (T 10 A).
Contact an Authorised Service Centre.
No pressure.1. Compressor or
polymerization unit adjusted
incorrectly.
1. Act on compressor pressure
switch or the polymerisation unit
pressure regulator (13).
“TEMP” flashes on the display (10),
CYCLE LEDs flash and fast frequency
warning sounds.
1. The “temperature alarm”
system has tripped (see
point 3, section 7.2).
1. Press one of the four CYCLE
(18, 19, 20, 21) keys to reset the
polymerization unit and contact

Authorised Service Centre.
Sudden interruption and reset of
selected work cycle and pressure
release.
1. Accidental opening of
polymerization chamber lid.
1. Re-close the polymerization
chamber lid and reset the data.
Pressure escapes during routine
operation.
1. Activation of overpressure
valve inside the
polymerization unit because
pressure has increased
beyond set value.
1. Situation part of normal operation
(see point 5, section 7.2).
Work cycle does not start after
pressing the relative key.
1. Polymerization chamber
lid not closed properly.
1. Close polymerization chamber by
rotating handle (8) properly so that
it presses downwards on the safety
microswitch (7).
During equipment installation the
basket (4) cannot be inserted properly
in the polymerisation chamber.
1. Sintered filter under
basket support grating
positioned incorrectly.
1. Position sintered filter properly.
If the problem persists, contact an

Authorised Service Centre.
To read all the documents in PDF format, you need to download a PDF viewer program. We suggest Adobe® Acrobat® Reader program, available for free from the following web site: www.adobe.com Note: programs versions are available for all operating systems.

© Zhermack SpA - All rights reserved - Via Bovazecchino, 100 45021 Badia Polesine (RO), Italy
Tel. +39 0425 597611 - Fax. +39 0425 53596 - Email web@zhermack.com
P.IVA 00594630295 - C.F. P.IVA IT00594630295 - R.E.A. 86603 - R.I. RO 00594630295 - M. RO 001381Isc. Reg. A.E.E. IT07111000002 - Cap. Soc. € 1.032.000,00

Credits - Terms and Conditions of Use - Work with us